Furnace Installation for Custom Construction in Conroe, TX

The demand for housing in Conroe, Texas is on the rise, and new home builders are stepping up to ensure that there is an adequate supply to meet it. Determining which climate control systems to use isn’t the most glamorous part of custom home design, but it’s an essential one. General contractors and future homeowners who want to take a more active role in designing their custom homes can find out what they need to know about Heater Installation below.

Best Options for New Construction

Future homeowners and designers have a lot of leeways when it comes to choosing a heating system. When replacing existing units, heating contractors often recommend sticking with the same fuel source and using the home’s existing ductwork instead of undertaking expensive retrofit jobs. Those aren’t issues in new homes, though, so all the options are on the table.

Single-Stage Furnaces

The primary appeal of single-stage furnaces is that they have a comparatively low upfront cost. However, homeowners who have it in the budget to build custom houses usually have the luxury of prioritizing long-term savings. They should know that single-stage furnaces are less efficient than the alternatives since they only operate on high, regardless of the indoor or outdoor temperature.

Two-Stage Furnaces

Two-stage furnaces operate at two capacities: high and low. They’re more efficient than single-stage furnaces and provide more consistent heat distribution. The trade-off is that they also cost more.

Variable-Speed Furnaces

Variable-speed furnaces are the most efficient type of traditional heating system. They control the flow of heated air to living areas of the home based on the indoor temperature, allowing them to maintain optimal climate control using minimal energy inputs. Variable-speed furnaces require a large upfront investment, but they cost less to operate in the long run since they’re far more efficient than either single-speed or variable-speed models.

Choosing an Energy Source

Homeowners have three options when it comes to powering their furnaces: natural gas, heating oil, and electricity. Each of these fuel sources comes with its own set of advantages and disadvantages, and no one solution is right for every home. Here’s how they compare:

Initial Investment

Furnace Installation costs vary significantly even within the same fuel types. That said, electric furnaces are almost always the least expensive to buy and install in new homes. Natural gas and heating oil furnaces need vent systems, piping, and electrical wiring. The added material and labor costs associated with new installations make them less cost-efficient in the short-term.

Operating Costs

The cost for different fuel sources varies significantly depending on availability. In areas that have municipal natural gas lines, it may be cheaper to pay a monthly gas bill. Households equipped with large solar arrays may be able to take advantage of free electricity, bringing the cost of operating electric furnaces close to zero. When in doubt, ask a local heating contractor for his or her professional opinion about fuel types.

Energy Efficiency

Modern furnaces are very energy efficient, but there’s a clear winner in this category. Electric furnaces convert nearly 100% of the electricity they consume into heat, while all fossil fuel-based systems carry some efficiency loss.

In many cases, it’s still less expensive to burn fossil fuels, even if the units are less than 100% efficient. However, the consumer cost doesn’t take environmental repercussions into account. Eco-conscious homeowners almost always prefer electric furnaces because they create no emissions.

Sizing the Furnace

There’s no one-size-fits-all solution for home heating. Homebuilders and designers need to take factors like the building’s size and thermal efficiency into account. Homeowners are better off leaving the work of sizing furnaces to the experienced Heating Services experts. They’ll consider:

    • The heat output of each system
    • How many British Thermal Units (BTUs) of heat per square foot will be required to keep the home comfortable
    • The Annual Fuel Utilization Efficiency (AFUE) rating of each unit
    • The family’s comfort needs and goals
    • The homeowner’s budget

An undersized furnace won’t be able to produce sufficient heat to keep the home warm during the coldest days of winter. An oversized unit won’t operate efficiently. Home heating contractors can help future homeowners, designers, or building contractors identify a comfortable middle ground and narrow down choices to appropriately sized models.

Don’t Get Left Out in the Cold

Looking for a heating and cooling company to install a furnace in a new custom home in Conroe? New Horizon A.C., Heating Inc. can help. Visit their website to learn more about their services or call (936) 494-1665 to speak with a representative today.